View AUD10W_4134513.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Technical Reference Note Ultra Low Profile AUD 10W Series
AUD 10W Ultra Low Profile DC - DC Module (Pb-free reflow compatible and ROHS Compliant)
The AUD 10W series is Astec's new Ultra Low Profile, 48Vin, SMT isolated single output modules. With the Ultra Low Profile SMT design (only 4.3mm height), the module can be flexible mounted on the top side or the bottom side of motherboard. The AUD 10W series also comes with enhanced features such as Remote on/off (RC), parallel application (PO), Power Good (ALM), and the protection of OVP, OCP and UVLO.
Electrical Parameters Input
Input range Efficiency 36 - 60Vdc 60 - 75Vdc (forced air 0.5m/s) 89% @5Vo
Control
Enable ON: RC pin connected to -Vin or Open OFF: RC pin connected to +Vin
Output
Line / Load Regulation Ripple and Noise OVP OCP +5%, -3% 50mVp-p 120% of Vonom (Latchup) 3.1A for 1.5V -3.3V 2.1A for 5V 95% of Vonom (1.5V) 90% of Vonom (others) (Latch-up) 1500VDC (1 minute)
Special Features
* Ultra Low Profile - 4.3mm height
LVP
* Efficiency - 89% @ 5V * -40 C to +85C Ambient Operating temperature
(0.2m/s air flow)
Isolation
* Open Frame SMT
* Low output ripple and noise
* Regulation to zero load * CISPR22, Class A for Conduct and Radiated EMI
* * * Parallel Application UL/cUL 1950, CE Mark Pb-free reflow compatible and ROHS Compliant
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 1 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
AUD 10W Ultra Low Profile Series THIS SPECIFICATION COVERS THE REQUIREMENTS
MODEL NAME AUD03M48 AUD03Y48 AUD03G48 AUD03F48 AUD02A48
SIS CODE AUD03M48 AUD03Y48 AUD03G48 AUD03F48 AUD02A48
Vout,Iout 1.5V @ 3.5A 1.8V @ 3A 2.5V @ 3A 3.3V @ 3A 5V @ 2A
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 2 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
Electrical Specifications
STANDARD TEST CONDITION on a single unit, unless otherwise specified. T A: 25C (Ambient Air) +Vin (P16-17): 36 - 60Vdc 60 - 75Vdc (forced air 0.5m/s) -Vin (P18-19): Return for +Vin RC (P13): Open +Vo (P2-4): Connect to load -Vo (P5-6): Return for +Vo PO (P14): Open ALM(P12): Open ABSOLUTE MAXIMUM RATINGS Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or in any other conditions in excess of those given in the operational sections of the specs. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Input Voltage Continuous Continuous (0.5m/s LFM) Transient (200s, 42V/10/s rate) Operating Temperature (0.2m/s air flow) Storage Temperature Operating Humidity INPUT SPECIFICATIONS Parameter Operating Input Voltage Input Voltage (0.5m/s LFM) Turn-on Voltage Turn-off Voltage Maximum Input Current2 (VIN = 0 to VIN,max; IO = IO,max) Device Symbol VIN VIN Min 36 60 32 30 Typ 48 Max 60 75 36 34 Unit Vdc Vdc Vdc Vdc Device Symbol VIN VIN VIN,trans Min 36 60 Typ Max 60 75 90 Unit Vdc Vdc Vdc
-40 All All TSTG -40 10 -
85 90 95
C C %
All
IIN,max
-
-
0.5
A
Note: 1. This power module is not internally fused. The use of an input line fuse (GMA-10A Bussman fuse or equivalent) is recommended. 2. The value is static only and rated for UL/cUL safety. In-rush current to charge internal capacitors is not specified.
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 3 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
OUTPUT SPECIFICATIONS Parameter Output Voltage Setpoint (VIN=VIN,min to VIN,max at IO=IO,max) Device AUD03M48 AUD03Y48 AUD03G48 AUD03F48 AUD02A48 Symbol VO,SET VO,SET VO,SET VO,SET VO,SET Min Typ 1.5 1.8 2.5 3.3 5.0 Max Unit Vdc Vdc Vdc Vdc Vdc
Output Regulation: Line: VIN=VIN,min to VIN,max Load: IO=IO,min to IO,max Output Ripple and Noise Peak to Peak: 5Hz to 20MHz Output Current Range
All All
-
-3 -3
-
+5 +5
% %
2.5V 1.5V 1.8V 2.5V 3.3V 5.0V 1.5V 1.8V 2.5V 3.3V 5.0V
IO IO IO IO IO IO IO IO IO IO
0 0 0 0 0 -
-
50 3.5 3 3 3 2 -
mVPK-PK A A A A A A A A A A
Output Current Limit Inception3
3.6 3.1 3.1 3.1 2.1
Over Voltage Protection Low Voltage Protection
All 1.5V others
120 95 90
%Vo %Vo %Vo
Efficiency Ta = 25C. Vin =48V, Io=Iomax
1.5V 1.8V 2.5V 3.3V 5.0V
77 79 81 83 84
82 84 86 88 89
-
% % % % %
Note: 3. This feature is only for module protection and is not intended for customer application. The value is specified at 25C ambient air temperature.
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 4 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
OUTPUT SPECIFICATIONS (Continued) Parameter Switching Frequency Device 1.5V 1.8V 2.5V 3.3V 5.0V Symbol Min Typ 670 520 600 640 640 Max Unit KHz KHz KHz KHz KHz
Dynamic Response: Slew Rate Load Change: 50% - 100% IO,max Load Change: 100% to 50% IO,max Turn-On time (Input to Output)5 IO = Iomax; VIN = VIN,nom to VO,nom
All All All All
IO/t -
15
0.3 x Io / 100uS -
10 10 250
A/s %VO %VO ms
Note: 5. Input to Output Turn-On time is defined as the difference between t1 and t2: where t1 is the time when the input voltage reaches the minimum VIN (VIN = VIN,MIN) and t2 is the time when the output voltage reaches it's specified range (VO = VO,SET-Min).
ISOLATION SPECIFICATION Input to Output Isolation: 1500Vdc (1 minute)
SAFETY APPROVAL The AUD (10W) is certified under the following agencies: * UL/cUL 1950, and CE Mark.
The module shall not be considered approved and carry safety agency logos until this has been authorized by Safety and QA / QC management.
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 5 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
Basic Operation and Features
Over Current Limit Inception (OCP) The Isolated DC-DC converter limits output current when the current is over the maximum output current due to abnormality such as overload or short circuit. When over current condition continues and output voltage decreases to the point of low voltage protection, the DC-DC converter will be in latch up mode. To restore the output, remove the abnormality and re-set the input voltage under 5V for 1 second minimum. Over Voltage Protection (OVP) The Isolated DC-DC converter stops the operation when the output voltage is over the specified Over Voltage Protection point, the converter will be in latch up mode after 0.5ms*. To restore the output, re-set the input voltage under 5V for 1 second minimum. Notes*: Output voltage might exceed the point at which OVP starts to function under the specific condition of transient input voltage or output current change. Therefore, OVP is set to wait for the mask time 0.5ms. Low Voltage Protection (LVP) If output voltage is under the specified Low Voltage Protection point, the converter will halt the operation. After typical 500ms mask period, the converter will be in latch up mode. To restore the output, re-set the input voltage under 5V for 1 second minimum. Remote On/Off Control (RC) If RC pin is open or connected to -Vin, the converter is turned on. If RC is connected to +Vin, the converter is turned off. Alarm Output (ALM) The Alarm output will be down to the -Vin level (Open Drain Output) at the condition of Over Voltage Protection or Low Voltage Protection. The maximum sink current in ALM pin is 10mA. When operating in parallel application, all operating units can be simultaneously halt by connecting all the ALM pins together, in the condition of Over Voltage Protection or Low Voltage Protection caused by any single converter. Maximum number for parallel operation is 10 units Synchronous Turn On/Off Connect the PO (parallel Operation) pins of all operating units together will synchronize the turn on / off time in parallel application.
MODULE PIN ASSIGNMENT
PIN # P1, 10, 11, 20 P2, 3, 4 P5, 6 P12 P13 P14 P15 P16, 17 P18, 19
DESIGNATION NC +Vo -Vo ALM RC PO NC +Vin -Vin
Mechanical supplemental contact pins + Output - Output Alarm Output Remote On/Off Parallel Operation + Input - Input
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 6 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
Performance Curves
Efficiency at 25C 100
Efficiency at 25C 100 Efficiency (%)
Vin=36V Vin=48V Vin=60V Vin=75V
Efficiency (%)
80 60 40 20 0 0 1 2 Iout (A) 3
80 60 40 20 0 0 1 Iout (A) 2 3
Vin=36V Vin=48V Vin=60V Vin=75V
Efficiency vs. Load Current Curves for 1.5Vo
Efficiency vs. Load Current Curves for 1.8Vo
E fficiency at 25C 100
100
Efficiency at 25C
Efficiency (%)
80 60 40 20 0 0 1 Iout (A) 2 3
Vin=36V
80 Efficiency (%)
Vin=48V Vin=60V Vin=75V
Vin=36V Vin=48V Vin=60V
60 40 20 0 0 1 Iout (A) 2 3
Vin=75V
Efficiency vs. Load Current Curves for 2.5Vo
Efficiency at 25C 100 80 Efficiency (%) 60 40 20 0 0.0 Vin=36V Vin=48V Vin=60V Vin=75V
Efficiency vs. Load Current Curves for 3.3Vo
0.5
1.0 Iout (A)
1.5
2.0
Efficiency vs. Load Current Curves for 5.0Vo
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 7 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
AUD Series Power derating
75C
100 80 Output (%) 60 40 20 0 -40 -20 0 20 40 60 80 Ambient Temp (C)
Air V = 0m/s Air V=0.2m/s
80% at 85C
Derating Curve for the AUD Series
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 8 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
Typical Application Circuit
A) Single Operation
GND -48V Fuse SW
+Vin -Vin -PO RC
ALM
+Vout -Vout
Load
SW Open : Enable DC-DC converter
Figure 1 B) Parallel Operation (A single power supply connects to multiple DC-DC converters to apply for higher output current more than rated one from a DC-DC converter)
GND -48V Fuse SW
+Vin -Vin -PO RC
ALM
+Vout -Vout
Load
+Vin -Vin -PO RC
ALM
SW Close : Halt all DC-DC converter with RC connected together Maximum units in parallel: 10pcs
+Vout
-Vout
Figure 2 i) All PO pins should be connected together ii) All DC-DC converters with ALM pins connected will stop the operation when one single converter is halted in mode protected by LVP or OVP. iii) LED is optionally connected to ALM pin for the notice of DC-DC converter stoppage.
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 9 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
C) Multiple Operation: A single power supply connects to multiple DC-DC converters to individually distribute output current to multiple independent loads.
GND -48V Fuse SW
+Vin -Vin PO RC
ALM
+Vout -Vout
Load
+Vin -Vin PO RC
SW Close : Halt all DC-DC converter with RC connected together
+Vout
-Vout
Load
ALM
Figure 3 i) All DC-DC converters with ALM pins connected will stop the operation when one single converter is halted in mode protected by LVP or OVP. ii) LED is optionally connected to ALM pin for the notice of DC-DC converter stoppage.
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 10 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
D) complex parallel and multiple (Sequence start-up): Two converters supplying the same output voltage for a single load and another converter supplying the different output voltage for another load.
Converter No.1
GND -48V
Fuse SW2 SW1
+Vin -Vin PO RC ALM
+Vout -Vout
Load
Converter No.2
+Vin -Vin PO RC ALM
+Vout -Vout
Converter No.3
+Vin -Vin PO RC ALM
+Vout -Vout
Load
SW1 Close : Halt DC-DC converter No.1 and 2 SW2 Close : Halt DC-DC converter No.3
Figure 4
i) PO pins of the converters supplying the same output voltage are connected to the others and another PO pin of the different output voltage converter is not connected. ii) All three DC-DC converters, which are connected to ALM pins, stop their operation when a single one is halted in mode protected by LVP or OVP. iii) LED is optionally connected to ALM pin for the notice of DC-DC converter stoppage.
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 11 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
Mechanical Specifications
2.17+/-0.5 20 P 19 18
OUTPUT= G . H V J K L A
Marking of No.1 pin
1 2 3
AUD0 E F 48
INPUT=36-60VDC
4 27.2+/-0.5 5 6 ABCD
17 P 10.3+/-0.2 16 15 14 13 P P P
1.5+/-0.2
P
0.25+/-0.1
+0.1
P
0.55 -0.15
0to10deg. 1.3+/-0.3
(4P)
US
12
C
10
11 (2.17)
37.3+/0.5
P
P
Label
4.3max 39.9+/-0.6 Coplanarity Max0.1mm
Pin No 1,10,11,20 2 3 4 5 6
Symbol NC +Vout +Vout +Vout -Vout -Vout
Function Mechanical supplemental contact pins +Output +Output +Output -Output -Output
Pin No 12 13 14 15 16 17 18 19
Symbol ALM RC PO NC +Vin +Vin -Vin -Vin
Function Alarm output Remote on/off control Parallel operation +Input +Input -Input -Input
Notes:
A : Factory symbol B : The last number of production year Example: 2 stands for 2002 C : Production month (1,2,3,.....,9,O, N, D) D : Blank
Unit Weight: 7.3g
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 12 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
PACKING AND SHIPPING Trays Tray Dimensions Unit : mm General tolerance : +-1.5
P1 by 5 = 219.5
P1 43.9
274.0
300
7.5 P2 53.7 P2 by 2=107.4 200 46.3
174.0
B-B' cross section
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 13 OF 15
A-A'cross section
Technical Reference Note Ultra Low Profile AUD 10W Series
Maximum pieces per a tray : 18pcs/tray Package Corrugated cardboard box contains trays with products. Tray is heaped with alternately opposite direction to prevent products from contacting against the bottoms of trays.
Dummy tray
Trays containing products Bottom sheet of corrugated card board
(310) (210) Label
(68)
ASTEC Products
Corrugated card board box
Numerals in parentheses are reference only. Unit : mm Label written by : Part Number, : Quantity, : Inspection Number. : CE Mark
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 14 OF 15
Technical Reference Note Ultra Low Profile AUD 10W Series
Reflow Soldering Information
Soldering I) Flux Solder the products with Rosin Flux (0.2wt%. chloride or less). Do not use acid or soluble flux, because they may damage metallic parts and glass parts and may cause defective or reduce quality. II) Solder SnAgCu solder compatible III) Condition of Soldering - Recommended soldering profile (J-STD-020C): Reflow Profile : Infrared or air blow Preheating : 150 - 200 deg C for 60 to 150sec Peak temperature : 240 5 deg C at surface. Maximum period above 220deg.C : 20 - 60sec Ramp rate : lower than 4 deg C / sec Times : Max 2 times (see below recommendation) . Recommendation Do not give vibration to products while solder melts under reflow process. Please handle to wait for products cooled down enough. Please don't reflow a motherboard mounted the products on the lower side such as a below figure, because the products surely fall down from the motherboard. If need, we recommend to use supplemental mechanical contact to pins at four corners of a substrate by other adhesive methods, for example, a thermal setting resin rather than soldering.
Motherboard
Isolated DC-DC converter
Recommend Storage Condition
Maximum storage period: Storage condition: 6 months 30 deg C, 60%RH
Recommend baking the module at 100degC for 24 hours if storage period is longer than 6 months.
MODEL : AUD 10W SERIES April 05 REVISION 02
SHEET 15 OF 15

▲Up To Search▲

Price & Availability of AUD10W

	To Download AUD10W Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .